--- discourse: 13223 --- (network-acls)= # How to configure network ACLs ```{note} Network ACLs are available for the {ref}`OVN NIC type `, the {ref}`network-ovn` and the {ref}`network-bridge` (with some exceptions, see {ref}`network-acls-bridge-limitations`). ``` ```{youtube} https://www.youtube.com/watch?v=mu34G0cX6Io ``` Network {abbr}`ACLs (Access Control Lists)` define traffic rules that allow controlling network access between different instances connected to the same network, and access to and from other networks. Network ACLs can be assigned directly to the {abbr}`NIC (Network Interface Controller)` of an instance or to a network. When assigned to a network, the ACL applies to all NICs connected to the network. The instance NICs that have a particular ACL applied (either explicitly or implicitly through a network) make up a logical group, which can be referenced from other rules as a source or destination. See {ref}`network-acls-groups` for more information. ## Create an ACL Use the following command to create an ACL: ```bash lxc network acl create [configuration_options...] ``` This command creates an ACL without rules. As a next step, {ref}`add rules ` to the ACL. Valid network ACL names must adhere to the following rules: - Names must be between 1 and 63 characters long. - Names must be made up exclusively of letters, numbers and dashes from the ASCII table. - Names must not start with a digit or a dash. - Names must not end with a dash. ### ACL properties ACLs have the following properties: % Include content from [../metadata.txt](../metadata.txt) ```{include} ../metadata.txt :start-after: :end-before: ``` (network-acls-rules)= ## Add or remove rules Each ACL contains two lists of rules: - *Ingress* rules apply to inbound traffic going towards the NIC. - *Egress* rules apply to outbound traffic leaving the NIC. To add a rule to an ACL, use the following command, where `` can be either `ingress` or `egress`: ```bash lxc network acl rule add [properties...] ``` This command adds a rule to the list for the specified direction. You cannot edit a rule (except if you {ref}`edit the full ACL `), but you can delete rules with the following command: ```bash lxc network acl rule remove [properties...] ``` You must either specify all properties needed to uniquely identify a rule or add `--force` to the command to delete all matching rules. ### Rule ordering and priorities Rules are provided as lists. However, the order of the rules in the list is not important and does not affect filtering. LXD automatically orders the rules based on the `action` property as follows: - `drop` - `reject` - `allow` - Automatic default action for any unmatched traffic (defaults to `reject`, see {ref}`network-acls-defaults`). This means that when you apply multiple ACLs to a NIC, there is no need to specify a combined rule ordering. If one of the rules in the ACLs matches, the action for that rule is taken and no other rules are considered. ### Rule properties ACL rules have the following properties: % Include content from [../metadata.txt](../metadata.txt) ```{include} ../metadata.txt :start-after: :end-before: ``` (network-acls-selectors)= ### Use selectors in rules ```{note} This feature is supported only for the {ref}`OVN NIC type ` and the {ref}`network-ovn`. ``` The `source` field (for ingress rules) and the `destination` field (for egress rules) support using selectors instead of CIDR or IP ranges. With this method, you can use ACL groups or network selectors to define rules for groups of instances without needing to maintain IP lists or create additional subnets. (network-acls-groups)= #### ACL groups Instance NICs that are assigned a particular ACL (either explicitly or implicitly through a network) make up a logical port group. Such ACL groups are called *subject name selectors*, and they can be referenced with the name of the ACL in other ACL groups. For example, if you have an ACL with the name `foo`, you can specify the group of instance NICs that are assigned this ACL as source with `source=foo`. #### Network selectors You can use *network subject selectors* to define rules based on the network that the traffic is coming from or going to. There are two special network subject selectors called `@internal` and `@external`. They represent network local and external traffic, respectively. For example: ```bash source=@internal ``` If your network supports [network peers](network_ovn_peers.md), you can reference traffic to or from the peer connection by using a network subject selector in the format `@/`. For example: ```bash source=@ovn1/mypeer ``` When using a network subject selector, the network that has the ACL applied to it must have the specified peer connection. Otherwise, the ACL cannot be applied to it. ### Log traffic Generally, ACL rules are meant to control the network traffic between instances and networks. However, you can also use them to log specific network traffic, which can be useful for monitoring, or to test rules before actually enabling them. To add a rule for logging, create it with the `state=logged` property. You can then display the log output for all logging rules in the ACL with the following command: ```bash lxc network acl show-log ``` (network-acls-edit)= ## Edit an ACL Use the following command to edit an ACL: ```bash lxc network acl edit ``` This command opens the ACL in YAML format for editing. You can edit both the ACL configuration and the rules. ## Assign an ACL After configuring an ACL, you must assign it to a network or an instance NIC. To do so, add it to the `security.acls` list of the network or NIC configuration. For networks, use the following command: ```bash lxc network set security.acls="" ``` For instance NICs, use the following command: ```bash lxc config device set security.acls="" ``` (network-acls-defaults)= ## Configure default actions When one or more ACLs are applied to a NIC (either explicitly or implicitly through a network), a default reject rule is added to the NIC. This rule rejects all traffic that doesn't match any of the rules in the applied ACLs. You can change this behavior with the network and NIC level `security.acls.default.ingress.action` and `security.acls.default.egress.action` settings. The NIC level settings override the network level settings. For example, to set the default action for inbound traffic to `allow` for all instances connected to a network, use the following command: ```bash lxc network set security.acls.default.ingress.action=allow ``` To configure the same default action for an instance NIC, use the following command: ```bash lxc config device set security.acls.default.ingress.action=allow ``` (network-acls-bridge-limitations)= ## Bridge limitations When using network ACLs with a bridge network, be aware of the following limitations: - Unlike OVN ACLs, bridge ACLs are applied only on the boundary between the bridge and the LXD host. This means they can only be used to apply network policies for traffic going to or from external networks. They cannot be used for to create {spellexception}`intra-bridge` firewalls, thus firewalls that control traffic between instances connected to the same bridge. - {ref}`ACL groups and network selectors ` are not supported. - When using the `iptables` firewall driver, you cannot use IP range subjects (for example, `192.0.2.1-192.0.2.10`). - Baseline network service rules are added before ACL rules (in their respective INPUT/OUTPUT chains), because we cannot differentiate between INPUT/OUTPUT and FORWARD traffic once we have jumped into the ACL chain. Because of this, ACL rules cannot be used to block baseline service rules.